Endless hot water, lower gas bills, and a unit sized for your home

Tankless Water Heater Installation Littleton CO Done Right

If your tank heater is rusting out or you're tired of running out of hot water mid-shower, tankless water heater installation Littleton CO homeowners trust starts with a proper load calculation and a code-correct install. We handle gas and electric on-demand units, venting, and permits for homes across Arapahoe County. Most installs wrap in a single day.

↗
Fast online booking

Request service today

Tell us what is happening. Our local team will confirm your visit shortly.

No spam. No obligation. Just practical help.
Thanks — we'll call shortly to confirm your visit.
Experienced Plumber Littleton CO professionals at work
Careful work. Honest options.
About this service

Tankless Water Heater Installation Littleton CO

Tankless water heater installation Littleton CO is the process of replacing a storage-tank water heater with a wall-mounted on-demand unit that heats water only when a fixture calls for it. We size the unit to your home's peak demand in gallons per minute, run a dedicated gas line or 240-volt circuit, install the correct Category III stainless vent, and pressure-test every connection before we leave. No tank means no standby loss, no 40-gallon limit, and no flood risk from a rusted-out shell sitting in your utility closet.

Littleton homes built before 1990 often have undersized gas lines and tight mechanical closets, which is why a tankless water heater install Littleton project here needs a real site assessment, not a big-box drop-in. We measure incoming water temperature, which runs about 48 to 52 degrees in winter, and confirm your meter can carry the added load. If you're weighing a conversion, we'll walk you through the numbers so you know exactly what you're getting.

  • ✓ Endless Hot Water
  • ✓ Lower Energy Bills
  • ✓ Frees Up Floor Space
  • ✓ Fewer Flood Risks
What's included

What's Included in a Tankless Install

Every tankless install we do includes the core work needed to get you hot water and pass inspection. Add-ons like gas line upgrades, panel work, or repiping are quoted separately and clearly before we start.

✓

Unit Sizing and Spec

We measure incoming water temperature, static and dynamic gas pressure, and peak fixture demand in GPM. Then we spec a unit that handles your coldest month, not the average. You get the model number in writing before install day.

✓

Removal and Disposal

We drain, disconnect, and haul away your old tank heater. That includes the tank, the venting, and any sediment or scale buildup. No old equipment left in your garage or on the curb.

✓

Gas or Electrical Hookup

Gas units get a dedicated line sized to the unit's BTU input, with a sediment trap and shutoff. Electric units get a 240-volt circuit with correct breaker and wire gauge. All connections are pressure-tested and code-compliant.

✓

Venting and Combustion Air

We install Category III stainless venting for gas units, routed to code with correct clearances and termination. Combustion air is verified so the unit burns clean. This is where cheap installs cut corners and fail inspection.

✓

Permits and Inspection

We pull the plumbing and gas permits through Arapahoe County and schedule the inspection. You don't chase paperwork. The inspector signs off, and you get the documentation for your records and resale.

✓

Startup and Walkthrough

We fire the unit, set outlet temp to 120 degrees, and run every hot fixture at once to confirm stability. You get a walkthrough of the controls, the maintenance schedule, and the warranty registration.

How it works

What Our Installation Process Looks Like

01

Phone Assessment

You call, we ask the right questions: fuel type, current heater size, how many bathrooms, and whether you've noticed low water pressure. We book a same-day or next-day site visit, usually within a 2-hour window. No charge for the estimate, no pressure to sign anything on the spot.

02

On-Site Sizing

A licensed tech measures incoming water temperature, static and dynamic gas pressure, and available venting routes. We calculate peak demand in GPM and pick a unit that handles your coldest winter inlet temp. This is where a lot of cheap installs fail, and it takes about 45 minutes.

03

Permits and Prep

We pull the plumbing and gas permits through Arapahoe County, order the unit, and schedule the install. Most permits clear in 1 to 3 business days. You get a written scope with the exact model number, venting plan, and total price before we touch a wrench.

04

Install Day

Install day runs 4 to 8 hours for a standard swap. We drain and remove the old tank, run new gas or electrical, mount the unit, install the Category III vent, and pressure-test every joint. Water's back on the same day, usually by late afternoon.

05

Test and Walkthrough

We fire the unit, set outlet temperature to 120 degrees, and run every hot fixture in the house at once to confirm flow and temperature stability. You get a walkthrough of the controls, the warranty paperwork, and the maintenance schedule. We don't leave until you've seen it work.

Tools & methods

Tools and Methods We Use

Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.

Pipe wrench and tube cutter

Used to break down the old tank connections and cut copper or PEX to exact length for the new supply lines. Clean cuts mean fewer leak points.

PEX crimping tool

For making code-compliant PEX tubing connections on supply lines. Faster and more reliable than soldering in tight utility closets.

Soldering torch

For copper pipe joints where PEX isn't the right call, like near the unit's hot outlet. We use lead-free solder per EPA Lead-Safe rules.

Pressure gauge

Used to verify static and dynamic gas pressure at the meter and at the unit's inlet. A tankless unit needs correct pressure to modulate properly.

Leak detection equipment

Electronic and soap-solution testing on every gas and water joint before we leave. We don't rely on smell or guesswork.

Pipe insulation and Teflon tape

Insulating hot and cold lines reduces heat loss and prevents winter freeze issues. Teflon tape seals threaded gas and water connections.

Real results

Before and after.

40-Gallon Tank to 9 GPM Tankless

Before

A Ken Caryl family of 5 was running out of hot water by 7 a.m. The 12-year-old 40-gallon tank had sediment buildup and recovered in 35 minutes. Gas bill averaged $62 a month for water heating.

After

We installed a 9 GPM condensing gas tankless unit with a new dedicated gas line and Category III vent. Install took 7 hours. Gas bill dropped to $44 a month, and the family runs two showers plus laundry without a temperature dip.

Failed Tank to Exterior-Mounted Rinnai

Before

A 1920s bungalow near Historic Downtown Littleton had a 30-gallon tank that leaked onto the utility closet floor. The closet was too small for a bigger tank, and the gas meter was undersized for a tankless unit.

After

We upgraded the gas line from the meter, mounted a Rinnai unit on the exterior wall, and vented directly out the back. Install took 9 hours over one day. Hot water is now endless, and the closet is empty and dry.

Electric Tank to Compact Electric Tankless

Before

A condo owner in Littleton Village had a 12-year-old electric tank that was rusting at the fittings. The HOA wouldn't allow a larger tank, and there was no gas service to the unit. Hot water ran out after one shower.

After

We installed a compact 240-volt electric tankless unit sized for 2 bathrooms and a kitchen. Required a 60-amp double-pole breaker and 6-gauge wire. Install took 5 hours. Hot water is now on demand with no tank to leak into the unit below.

Problems we solve

Problems a Tankless Install Solves

If any of these sound familiar, a tankless upgrade is worth pricing out. We'll tell you honestly whether it's the right move for your home.

Ask a pro →
01

Running out of hot water mid-shower

We size a tankless unit to your peak demand in GPM, so two showers, a dishwasher, and laundry can run at once without a temperature drop. Most Littleton homes land on an 8 to 10 GPM unit.

↗
02

Rusty water or popping sounds from the tank

We replace the failing tank with a wall-mounted tankless unit that holds less than a cup of water. No tank to rust, no tank to burst, no flood risk in your utility closet or basement.

↗
03

High gas bills from standby heat loss

Tankless units heat only when a fixture calls for water. Most homeowners see 20 to 30 percent lower water-heating costs, which on a typical Xcel bill runs $8 to $18 a month in savings.

↗
04

Tank won't fit in a tight utility closet

A wall-mounted tankless unit takes about 2 square feet and mounts on an interior or exterior wall. We find a vent path and mount the unit where it fits and stays serviceable.

↗
Transparent pricing

Tankless Installation Pricing in Littleton

$2,800 - $6,500 depending on unit size, gas line work, venting, and electrical upgrades

Typical 2026 pricing for tankless water heater installation in Littleton runs $2,800 to $6,500 depending on unit size, gas line work, venting, and whether you need an electrical panel upgrade. A straight gas swap with an existing vent path sits at the low end. Long vent runs, a new gas line from the meter, or a 200-amp panel upgrade push it higher. We give you a written price with the exact model number before we start, and we don't add charges on install day. If you're comparing on demand water heater installation Littleton CO quotes, ask each company whether permits and inspection are included. Ours are.

A tankless unit lasts about 20 years versus 10 to 12 for a tank, cuts water-heating costs 20 to 30 percent, and eliminates the flood risk of a failed tank. Over 15 years, the total cost of ownership usually beats a tank replacement, especially if you plan to stay in the home.

01Unit size and brand

An 8 GPM unit costs less than an 11 GPM condensing model. Rheem, Navien, Rinnai, and Bradford White all sit in different price bands. We quote the model that fits your demand, not the cheapest one on the shelf.

03Venting complexity

A short side-wall vent is straightforward. Long runs, roof termination, or routing through finished space adds labor and materials. Category III stainless venting costs more than PVC but is required for most condensing units.

04Electrical panel capacity

Electric tankless units need a 240-volt circuit, often 60 amps or more. If your panel is full or only 100 amps, a panel upgrade adds $1,500 to $3,000. We check this during the site assessment.

Proof you can check

Licensed, Insured, and Verified

✓
Colorado Master Plumber LicenseState of Colorado, Division of Professions and Occupations
✓
Colorado Journeyman Plumber LicenseState of Colorado, Division of Professions and Occupations
✓
Backflow Prevention CertificationState of Colorado approved training provider
✓
EPA Lead-Safe CertificationU.S. Environmental Protection Agency
✓
OSHA Safety CertificationOccupational Safety and Health Administration
Customer reviews

What Littleton Homeowners Say

★★★★★
“Our 15-year-old tank finally let go on a Sunday. These guys had a Navien unit spec'd and installed by Tuesday afternoon. They ran a new gas line from the meter, vented through the side wall, and pressure-tested everything. Water's been rock steady since, even with two showers and the dishwasher going.”
MT

Mark T.Homeowner, Ken Caryl

✓ Verified
★★★★★
“Got three quotes for tankless. These were the only ones who actually measured incoming water temp and calculated GPM. They spec'd a bigger unit than the others and explained why. Install took one day, hot water never runs out, and our gas bill dropped about $14 a month.”
DK

Dave K.Homeowner, Roxborough

✓ Verified
Good questions

Frequently Asked Questions

+1 (831) 293-1204

Most tankless water heater installation cost Littleton CO projects run $2,800 to $6,500 in 2026, depending on unit size, gas line upgrades, venting runs, and whether you need a panel upgrade for electric. A straight gas swap with an existing vent path sits at the low end. Long vent runs, a new gas line from the meter, or a 200-amp panel upgrade push it higher. We give you a written price before we start.

Yes, if you plan to stay in the home 5+ years. Tankless units last about 20 years versus 10 to 12 for a tank, cut water-heating bills 20 to 30 percent, and eliminate the flood risk of a failed tank. In Littleton, where winter inlet water runs 48 to 52 degrees, proper sizing matters more than the brand. We size to your coldest month, not the average.

A standard swap takes 4 to 8 hours on install day. Add 1 to 3 business days for the Arapahoe County permit to clear, plus a 15 to 30 minute inspection after. If we're running a new gas line from the meter or upgrading an electrical panel, plan on a second day. You'll have hot water back the same day in most cases.

Most Littleton homes with 2 to 3 bathrooms need a unit rated 8 to 10 gallons per minute at a 50-degree temperature rise. That covers two showers plus a dishwasher running at once. Homes with 4+ bathrooms or a large soaking tub usually need 10 to 11 GPM or two units in a manifold. We measure your incoming water temp and peak fixture load before we spec anything.

Ready when you are

Book Your Tankless Water Heater Installation Littleton CO

Licensed, insured, and pulling permits on every job. Call us for a same-day estimate on your tankless install and we'll give you a written price with the exact model and venting plan. No surprises on install day.

Get Free Estimate +1 (831) 293-1204 →
Request an appointment

Contact Us Today

Call us at +1 (831) 293-1204 or email info@plumberlittleton.com to schedule service or ask a question. We answer the phone 24/7 for emergencies and book same-day appointments during regular hours. If you are in Littleton or anywhere in Arapahoe County, we can get a plumber to your door fast.

Request received — our team will be in touch shortly.
Tap to call+1 (831) 293-1204